October 7, 2026

Resources
Products
Solutions

4 weeks ago

script_ex04 : Create binned models from point model cards

Requires: Utmost IV Minimum Versions: Utmost IV 2.20.0.R This example describes how to create BSIM4 binned models given a bunch of point model cards. The point model cards used for

4 weeks ago

check_ex01 : Simulating Device Characteristics

Requires: Utmost IV, SmartSpice, SmartView Minimum Versions: Utmost IV 1.10.6.R, SmartSpice 4.10.2.R, SmartView 2.28.2.R This example describes how to use the model check module to simlulate some mosfet characteristics. The

4 weeks ago

check_ex02 : Simulating Extracted Characteristics

Requires: Utmost IV, SmartSpice, SmartView Minimum Versions: Utmost IV 1.10.6.R, SmartSpice 4.10.2.R, SmartView 2.28.2.R This example describes how to use the model check module to simlulate and display some mosfet

4 weeks ago

check_ex03 : Checking for Binned Model Discontinuities

Requires: Utmost IV, SmartSpice, SmartView Minimum Versions: Utmost IV 1.10.6.R, SmartSpice 4.10.2.R, SmartView 2.28.2.R This example describes how to use the model check module to check for binned model threshold

4 weeks ago

cor_ex01 : Retargeting a Model Card

Requires: Utmost IV, SmartSpice, SmartView Minimum Versions: Utmost IV 2.19.2.R, SmartSpice 5.2.0.R, SmartView 2.2207.0.R This example shows how to use the Utmost IV Corner and Retargeting module to generate an

4 weeks ago

cor_ex02 : Creating Corner Models

Requires: Utmost IV, SmartSpice, SmartView Minimum Versions: Utmost IV 2.19.2.R, SmartSpice 5.2.0.R, SmartView 2.2207.0.R This example shows how to use the Utmost IV Corner and Retargeting module to generate typical,

4 weeks ago

cor_ex03 : Parameter Selection for Corner Model Extraction

Requires: Utmost IV, SmartSpice, SmartView Minimum Versions: Utmost IV 2.19.2.R, SmartSpice 5.2.0.R, SmartView 2.2207.0.R This example shows how to perform the parameter selection needed in the Utmost IV Corner and

4 weeks ago

cor_ex04 : Creating Corner Models Using Targets with Preliminary Extraction

Requires: Utmost IV, SmartSpice, SmartView Minimum Versions: Utmost IV 2.19.2.R, SmartSpice 5.2.0.R, SmartView 2.2207.0.R This example shows how to use the Utmost IV Corner and Retargeting module to generate typical,

4 weeks ago

vwfex01 : Stress in MOSFET with Embedded SiGe Layer

Requires: VWF, ATHENA, This example demonstrates simulation of stresses in a test MOSFET structure with an embedded SiGe layer. All important geometrical characterisics of the test structure, including thicknesses of

4 weeks ago

vwfex02 : VT Optimization Using a DOE Approach

Requires: VWF, ATHENA, ATLAS The objective is to optimize 4 process parameters (gate oxide time, temperature, Vt adjust implant dose, and energy) in order to get a targetted Vt of

4 weeks ago

vwfex03 : VT Optimization Using an Optimization Approach

Requires: VWF, ATHENA, ATLAS The objective of this example is to optimize 4 process parameters (gate oxide time and temp as well as Vt adjust implant dose and energy) in

4 weeks ago

vwfex04 : Back End Capacitance Optimization

Requires: VWF, CLEVER This example demonstrates the use of CLEVER within VWF. You should be familiar with CLEVER syntax before running this example. Please refer to the CLEVER manual for